HD-SF Solder Free DIY Build Kit (MR-30 Quick Connection)

*IN STOCK - Now shipping with the NEW T-Motor F7 HD flight controller*

Now Available with:

• HD1 5" Frame
• Skyeliner HD Frame
• Moxy Frame
• HD1-VS Frame
  
• DJI Digital FPV Remote Controller
• DJI FPV Goggles V2
  

Drone Building has never been easier!
The HD-SF Solder Free Build Kit is quick and easy to assemble, and comes ready to go with ZERO soldering or programming required - simply build the frame, plug all the components together, and you’re ready to fly!

Highlights:

• ZERO Soldering: Everything is 100% plug-n-play, the MR30 Quick Connection System makes assembly a breeze and removes the need for any soldering!

• ZERO Programming: No Betalight or ESC programming required, all of the MR-30 T-motor Stacks will be pre-flashed with the latest version of betaflight and BLheli and will also include a complete Betaflight Tune and Configuration Setup. Pre-programmed to work on either 4s or 6s batteries.
  
• Recommended Battery:
• R-Line Version 3.0 4s 1300mah 120C Battery
• R-Line 6s 1050mah 95C Battery
• 4S between 1300mah to 1500mah and a 90C or higher rating
• 6S between 1000mah to 1400mah and a 90C or higher rating

• Assembly Time: ~30 minutes - 2 hours

*If you are using a controller other than DJI, you will need to solder on the appropriate receiver.

View the HD1-SF Build Guide Here!

Get your replacement parts here!

Available GoPro Mounts:

• GoPro Hero 5/6/7 Mount
• GoPro Hero 8 Mount
• GoPro Hero 9 Mount
• GoPro Session Mount

FC Specifications

• Input Voltage: 12-25.2V
• MCU: STM32F722RET6
• IMU: BMI270
• OSD: Yes
• Blackbox: 16MB Onboard Flash
• Uarts: 6
• ESC Connections: 6
• Firmware: BetaFlight Target: TMOTOR F4
• BEC: 5V 2A /10V 2A
• LC Filter: Yes
• Current Sensor: Esc Telemetry / Current ADC
• Buzzer: Pads 
• Barometer: No
• Dimensions: 37x37x7mm
• Mounting Pattern: 30.5x30.5mm
• Weight: 7g

ESC Specifications

• Continuous current: 4*55A
• BLHeli_32 32bit
• Burst current: 4*75A
• BEC Output: 10V @2.0A
• Size: 45x41x7.3mm
• Weight: 17.3g (Including Heatsink)
• Support DSHOT150/300/600/1200
• Four soldered MR30 female connectors with 

• 77mm long #20 silicone wires

Frame Options:

• HD1-VS Frame
• Skyeliner HD Frame
• Moxy Frame

Includes:

• MR30 SF - T-motor F7 HD + F55a BLheli32 stack
• MR30 SF - Hypetrain Freestyle 2306 2450kv motors (19mm wire length)
• Caddx Air Unit Micro Version for DJI Digital HD FPV System
• 2 sets of HQ Juicy J37 4.9x3.7x3 Props

You Will Need:

• 2mm Hex Driver
• 1.5mm Hex Driver
• 8mm Box Wrench
• 5.5mm Box Wrench
• Double Sided Tape - VHB
• Electrical Tape
• Blue Loctite